Biological Contamination in the Anolyte System

Contents[Show]

Product Support and Customer Service

For Further support visit our Contact Page

Safety

Think and act in a safe manner. Always disconnect power and use a lockout before you work on the E-coat system, or any of the related subsystems. Observe any confined space conditions. Use the appropriate safety equipment and clothing for the task. Please carefully read all the instructions listed below to familiarize yourself with the project before attempting to perform any of the work.

Required Materials

Required Tools

General

The occurrence of biological growth in the anolyte system is a rather common nuisance to electro-coat operators. Sometimes the rapid degradation (pitting, etc.) of 316L anodes is thought to be the result of attack from the by-products of some forms of biological growth, but this has not been confirmed in a controlled laboratory test. Biological activity in the anolyte does not usually cause ED film defects. Biological growth is harmful in that it can clog anolyte return lines. This results in less cooling of the Cell (faster dissolution of the 316L anodes due to higher temperatures inside the Cell) and less acid removal by the anolyte system.

Biological growth generally falls into two broad categories – bacteria or fungus. Both of these types of organisms are everywhere. They are noticed in the anolyte solution because they have found a good food source and a nice place to live. Most of the time they die as fast as they multiply. However, in the anolyte solution they can thrive, especially if: 1) the anolyte conductivity is less than 1800 mSiemens/cm; 2) the anolyte is mostly DI water (after a flushing of the anolyte tank and acid is not added to increase the conductivity); 3) the anolyte fluid is ever stagnant (anolyte pump turned off); 4) warmer weather in the evenings (late spring and summer), 5) malfunction in the DI water system.

A coordinated effort should be made with the E-coat maintenance manager, ED paint company representative, local water treatment company representative, and a representative of UFS Corporation. These individuals can work together to find the source of the biological contamination and take action to reduce or eliminate the problem. UFS recommends that a sample be taken of the contamination and a culture test performed to identify the contamination. The ED paint company, local water treatment company or a local university may be able to offer assistance with the culture testing and analysis.

Once the anolyte system is attacked by a biological infestation, it is common for the organism to build multiple layers or colonies. Each of the colonies has a protective outer shell. Therefore, it will take a determined effort to remove the contamination from the anolyte system (cells, piping, valves, tank, etc.). Efforts to clean or eliminate the contamination may only remove one or two layers or colonies at a time, so treatments on successive weekends are usually necessary.

There are several strategies that can be used to avoid biological contamination, including:

Some of the more common biocides include copper, cupric acetate, silver nitrate, Kathon (Rohm & Hass) and Spectrus NX 1103. Important: Do not use any biocides that contain halides such as chlorides or bromides. Chlorides and bromides can attack the 316L anodes. Seek approval from UFSc before any biocide not listed above is used.

If biological growth is found in the anolyte, one of the preliminary tasks to be done is to plan the removal of the growth at the same time as plans are made to reduce the chances of reoccurrence. The steps below are meant to provide general assistance in removing the biological growth from the anolyte system. Please review these steps with your paint supplier. They may want you to drain your paint to prevent any possibility of the hydrogen peroxide getting into the paint bath.

Step 1

Drain the anolyte tank to just above the pump suction inlet to reduce the amount of neutralizer and solvent required. Estimate the volume of remaining anolyte in tank, piping, and TECTRONTM Anode Cells. See below:

Effective Length Est. Volume in Tectron T1 Anode Cell
<910 mm (36") 3 liters 0.75 gallons
<1400 mm (55") 5 liters 1.25 gallons
<1900 mm (74") 6.5 liters 1.7 gallons
<2900 mm (114") 10 liters 2.5 gallons

If you are using the 2” size TECTRON Cell, then increase the amount from the table above by 35%. For 3” size, double the amount. And for 5” size cells, triple the amount.

Step 2

Calculate amount of solvent needed to equal ~3% of total volume from Step 1 and add it to the anolyte tank.

Example:
Anolyte total from Step 1 = 200 l (50 gal)
200 l x 0.03 = 6 l (~1.5 gal) of solvent.

Step 3

Next adjust the pH based upon the type by adding (to the anolyte) small amounts of the neutralizer until the desired pH is met.

Step 4

Add the nylon strainer bag to the open end of the anolyte return manifold just before it enters the anolyte tank and attach with a stainless clamp-off plastic tie.

Step 5

After 24 hours of circulating this special cleaning solution, dump it to waste water treatment. Refill with D.I. Water and add enough neutralizer to get up to 80% of recommended anolyte conductivity. Turn on pump and circulate. Do not allow D.I. Water to stand.

Step 6

Repeat steps 1-5 the following weekend. Continue each weekend until no more paint solids are found in strainer bag or the current draw has returned to normal levels. Perform at least two (2) cleanings.

Step 7

If this cleaning does not work, then the next step is to perform mechanical cleaning to remove the biological growth. You can use a soft bristle bottlebrush to clean out the inside of the Membrane Shell, anolyte supply lines, and the Electrode. Flush out the manifolds by adding a clean out plug at each of the terminations. Use air pressure to blow out lines. NOTE: DO NOT PRESSURIZE THE INSIDE OF A MEMBRANE SHELL. Repeat Steps 1-5 after all the flushing and mechanical cleaning is over.

Troubleshooting:

Sometimes the occurrence of biological growth is accomplished by a rise in the pH of the ED paint bath. Check for biological growth in the post rinses. Biological growths can attach themselves (or fix) to acid groups. This results in a higher pH. When these biological growths are killed, it is possible some of the fixed acid groups become unattached and then begin to drive down the pH. Be careful when adding acid to the ED paint bath before the biological growths are removed from the post rinses.

Excessive pressure drop across Anode Cell:

One of the consequences of the growth of fungus is the blockage of the flow of anolyte through the Cells. This is especially critical for closed top Anode Cells. In these cases there can be a significant pressure drop across the Cell. The pressure drop is harmful because it can 1) cause anolyte to leak out from the fittings, and or 2) cause irreversible damage to the ion-exchange membrane. In either case anolyte will find its way into the ED bath, which can lead to poor performance and even defects.


BULLETIN 990101